The Oxygen sensors of all motorcycles are limited to catch the emission standards and in some specific throttle positions will try to alter the fuel mixture to catch the stoichiometric Air/Fuel ratio. This system is designed to improve emissions but has negative effect on performance.
Do you want to understand the advantages of using an O2 Eliminator?
- If you have an aftermarket exhaust, the O2 Eliminator adds about 3% more fuel, which helps your bike run better and cooler, and eliminates the "check engine" light without needing a fuel tuner.
- If you are using a fuel tuner like Power Commander, Bazzaz, Autotune, etc, the O2 Eliminator ensures that your engine runs on the fuel map you want, without any interference from the stock O2 sensor and ECU.
- It is essential for any Autotune module, providing better accuracy and consistent results during Dyno tuning.
- If your stock O2 sensor has burned out and you don’t want to spend a significant amount to replace it, the O2 Eliminator is the ideal solution.
- Stock bikes are designed to run very lean; adding a slight fuel enrichment can considerably improve rideability, throttle response, low-end torque, and operating temperature.
The Oxygen sensor eliminator kit by SmartMoto replaces the OEM unit and forces the ECU to use the installed map without the restrictions of the Oxygen sensor.
Key Features
- Improves throttle response, offering smoother power delivery and more torque in the low and mid RPMs.
- Supports aftermarket fuel controllers that require the elimination of the Oxygen sensor.
- Supplements the installation of aftermarket exhaust systems that do not have an Oxygen sensor port.
- Can be used to replace a malfunctioning Oxygen sensor.
- Plug and play design, no wire cutting required.
High Quality Standards
- We use only OEM connectors to ensure perfect fitment.
- The exhaust blanking plugs are highly corrosion resistant plugs.
- Sophisticated production and high quality parts ensure top quality product.
- This product is tested and developed for the listed motorcycles.
Installation
Fitting is very easy, you need to follow the wires from the oxygen sensor to the wiring harness until you find its connector, then you disconnect it and you connect the eliminator in its place.
Then you unscrew the sensor from the exhaust and install the blanking plug in its place.
For motorcycles that have two oxygen sensors we list eliminator kits that contain two eliminators, you use the procedure above for each oxygen sensor.
Compatible motorcycles
- Kawasaki > KLX 230 > 2020 - 2024
- Kawasaki > Ninja 400 (USA) > 2018 - 2022
- Kawasaki > Ninja 400 > 2018 - 2021
- Kawasaki > Ninja 650 (USA) > 2017 - 2022
- Kawasaki > Ninja 650 > 2017 - 2020
- Kawasaki > Versys 650 (USA) > 2015 - 2021
- Kawasaki > Versys 650 > 2015 - 2020
- Kawasaki > Versys-X 300 > 2017 - 2023
- Kawasaki > Vulcan S 650 (USA) > 2015 - 2024
- Kawasaki > Vulcan S 650 > 2015 - 2020
- Kawasaki > Z400 (USA) > 2019 - 2022
- Kawasaki > Z400 > 2019 - 2021
- Kawasaki > Z650 / RS (USA) > 2017 - 2023
- Kawasaki > Z650 / RS > 2017 - 2020
- Yamaha > FZ8 > 2010 - 2015
- Yamaha > MT-03 > 2016 - 2020
- Yamaha > MT-07 > 2014 - 2020
- Yamaha > MT-25 > 2018 - 2020
- Yamaha > T-MAX 530 > 2017 - 2019
- Yamaha > Tenere 700 > 2019 - 2020
- Yamaha > Tracer 700 / GT > 2016 - 2020
- Yamaha > Wolverine 1000 > 2018 - 2020
- Yamaha > Wolverine 850 > 2018 - 2020
- Yamaha > XSR 700 > 2016 - 2020
- Yamaha > YZF R1 > 2009 - 2014
- Yamaha > YZF R25 > 2014 - 2020
- Yamaha > YZF R3 > 2015 - 2020
